Thanks to the non-porous magic of Solid Surface materials, it has never been easier to keep your home or commercial workspace in pristine condition. Surfaces like Corian®, HIMACS, Staron, Hanex, Durasein, and Tristone are engineered to make your daily cleaning routine effortless by preventing dirt, moisture, and bacteria from getting a foothold.
Whether you are caring for a residential kitchen worktop, a hotel bathroom vanity unit, or a high-traffic healthcare counter, here is our complete Solid Surface cleaning and maintenance advice to keep your investment looking brand new for decades.
The Magic of Non-Porous Surfaces: Why Solid Surface Is So Easy to Clean
Unlike natural stone (such as marble or granite), which contains microscopic pores that absorb liquids and require periodic chemical sealing, Solid Surface is completely non-porous and homogeneous all the way through.
- Liquids Cannot Penetrate: Spills from red wine, coffee, curry, beetroot juice, or clinical disinfectants simply sit on top of the surface rather than soaking in.
- Seamless Hygiene: Because Solid Surface worktops, integrated sinks, and coved upstands are bonded together with inconspicuous seams, there are no open grout lines or silicone gaps where mould, mildew, and bacteria can multiply.
- No Sealing Required: You never need to apply waxes, polishes, or stone sealants to maintain its waterproof performance.
Step-by-Step: How to Clean Solid Surface
1. Everyday Routine Cleaning
For 95% of day-to-day spills, watermarks, and cooking residue, keep it simple:
- Wipe the surface down using warm soapy water or a standard ammonia-based household kitchen/surface spray and a damp microfibre cloth.
- Always buff dry with a clean, dry cloth or paper towel afterwards. Buffing the surface dry prevents hard-water limescale films from building up over time and keeps the finish looking consistent.
2. Removing Stubborn Marks, Coffee Rings & Stains
If a stubborn mark, food stain, or fine surface scuff does not lift with soapy water:
- Apply a mild cream abrasive cleaner—we strongly recommend Bar Keepers Friend (or Cif Cream)—onto a damp, non-scratch sponge (such as a white Scotch-Brite pad for matte/satin finishes).
- Rub gently over the area in small, overlapping circular motions.
- Rinse thoroughly with clean warm water and buff completely dry with a microfibre cloth. The mark will lift right out and the finish will return to its original glory.
3. Tackling Limescale Around Taps & Integrated Sinks
In hard-water areas like Essex and London, limescale can build up around tap bases and inside integrated Solid Surface bowls:
- Use a standard household limescale remover or a solution of diluted white vinegar, leave it for a few minutes to dissolve the mineral deposits, then rinse thoroughly with warm water and buff dry.
- To disinfect integrated sinks once a week, fill the bowl with warm water and add a small splash of diluted household bleach, let it stand for 15–20 minutes, then drain, rinse, and wipe dry.
What to Avoid (Protecting Your Surface)
While Solid Surface is exceptionally tough, following three golden rules will prevent avoidable damage:
- Always Use Trivets or Hot Rods for Hot Pans: Solid Surface is heat-resistant, but placing boiling pans, cast-iron skillets, or air fryers directly from the hob or oven onto the surface can cause scorching or thermal marks. Always use a trivet or heat pad.
- Never Cut Directly on the Worktop: Always use a chopping board. Slicing directly onto the worktop with sharp kitchen knives will leave score marks.
- Avoid Harsh Paint Strippers & Strong Acids: Keep oven cleaners, paint removers, drain unblocking acids, and acetone nail-varnish remover away from the surface. If accidentally spilled, flush immediately with plenty of cold soapy water.
A Quick Note on Finishes & Dark Colours
Most Solid Surface installations are finished in a practical matte or satin sheen. Darker, heavily pigmented colours and high-gloss finishes look dramatic, but they will naturally show dust, fingerprints, water spots, and fine micro-scratches more readily than light or mid-tone colours. If your surface ever suffers deeper scratches or heavy wear after years of service, our specialist team at BSF Solid Surfaces can professionally re-sand and refinish the worktop on-site to look like the day it was installed.
Have a question about caring for your Solid Surface or need a professional refurbishment? Call our team on 01277 263603 or email info@bsfsolidsurfaces.com.